ZLY630外链板加工工艺及夹具设计

论文编号:JX953  论文字数:10733.页数:32   附CAD图

摘     要
 此次设计是对ZLY630外链板的加工工艺和夹具设计，其零件为锻件，具有体积中等，零件结构简单的特点，由于面比孔易加工，在制定工艺规程时，就先加工面，再以面为基准来加工其它，其中各工序夹具都采用专用夹具，特别的对于加工圆弧的工序中，选一面两销的定位方式，并以操作简单的手动夹紧方式夹紧，其机构设计简单，方便且能满足要求。机械加工工艺是规定产品或零件机械加工工艺过程和操作方法。生产规模的大小、工艺水平的高低以及解决各种工艺问题的方法和手段都要通过机械加工工艺来体现。而机床夹具是在机床上用以装夹工件的一种装置，其作用是使工件相对于机床或刀具有个正确的位置，并在加工过程中保持这个位置不变。它们的研究对机械工业有着很重要的意义。
 
关键词：  外链板 加工工艺 专用夹具 设计

The processing craft and the jig design of ZLY630 outer chain plate
Abstract
    This design is the processing craft and the jig design of the ZLY630 outside chain plate, its components are the forging, it has the medium volume and simple structure components,Because the surface is easier than the hole to process, so when formulating the technological process, processing surface firstly，then processes other take the surface as the datum,In which various working procedures jig all uses the unit clamp, specially such as processing the arc, chooses locate mode of one surface two melt and the simple manual clamp way to clamp, its organization design is simple, convenience and also can satisfy the request. The machining process prescribes the machining process and operating methods of products and the components. The size of the production, the level of process and the methods and means to solve various process problems should be reflected by the machining process. The machine tool's fixture is a device to clamp workpiece in the machine, its function is to make the workpiece which relative to the machine or aword have a corret position, and keep this in the machining process. Their study has a very important significance for the mechanical industry.
 
 
Key words：  Outer chain plate，the processing craft，unit clamp，design

目  录
摘     要 I
Abstract II
目  录 III
第一章 绪 论 1
第二章  ZLY630外链板的分析 2
2.1 ZLY630外链板的工艺分析 2
2.2 ZLY630外链板的工艺要求 2
第三章 工艺规程设计 4
3.1 加工工艺过程 4
3.2 确定定位基准 4
3.2.1粗基准的选择 4
3.2.2精基准选择的原则 4
3.3工艺路线的拟订 5
3.3.1工序的合理组合 5
3.3.2加工阶段的划分 6
3.4确定切削用量及基本工时（机动时间） 7
第四章  镗孔夹具设计 15
4.1研究原始质料 15
4.2定位基准的选择 15
4.3切削力及夹紧力的计算 15
4.4 误差分析与计算 17
4.5 零、部件的设计与选用 18
4.5.1定位销选用 18
4.5.2夹紧装置的选用 19
4.6 夹具设计及操作的简要说明 19
第五章  铣R400圆弧夹具设计 21
5.1研究原始质料 21
5.2定位基准的选择 21
5.3 切削力及夹紧分析计算 21
5.4 误差分析与计算 23
5.5 零、部件的设计与选用 24
5.5.1定位销选用 24
5.6 夹具设计及操作的简要说明 25
结  论 26
参考文献 27
致  谢 28

相关论文