基于MCS51单片机的心率测试仪_电子信息工程-免费论文网

基于MCS51单片机的心率测试仪

论文编号:DZXX048 论文字数:10676,页数:35

摘要
心率是人体中一个非常重要的生命信息,而传统的脉诊由于其定性化和主观性影响了心率测试的精度,成为中医脉诊应用、发展和交流中的制约因素。为了提高对此类生物医学信号的测试精度,必须结合现代科学技术。
介绍一种以AT89S52为控制核心的智能人体心率检测装置的设计方法。利用光电传感器采集人体脉搏信号,经过前置级放大、滤波、积分比较等信号处理电路,将其转换成脉冲电压信号,再利用单片机对脉冲信号进行处理计算出心率并显示。由于传感器信号十分微弱,其幅度一般在微伏到毫伏的数量级范围,且夹杂着各种噪声和干扰,因此要求前置级放大电路具有高增益、高共模抑制比等技术指标。实现了微小信号放大、显示及报警功能。具有测量灵敏度高、实时性好、性价比高等优点。
本课题硬件设计用Protel99 SE工具，软件仿真用Keil c V3.60语言编程。系统经调试，功能稳定，均实现各项任务指标。

关键词：心率；滤波器；放大器；脉冲计数

ABSTRACT

Human heart-rate is a very important life information. But the traditional pulse diagnosis affected the accuracy of heart-rate testing because of its qualitative and subjective, which had some constraints as application of pulse diagnosis, development and communication. To improve the signal for such biomedical testing accuracy, modern heart-rate detecting must be combined with modern science and technology.
The design method of intelligent heart-rate measuring instrument was based on AT89S52. The pulse signal was collected by photoelectric-sensor, then converted into pulse voltage signal through the signal processing circuits of pre-amplifying, LPF, integral comparator. Finally, the pulse voltage signal was inputted the single chip microcomputer which calculated heart-rate and displayed the result. The sensor signal was so weakly that its amplitude was in the range of micro-voltage to MV, and including all kinds of noise and interference. Therefore the pre-amplifier must be high gain, high common-mode rejection ratio, and other technical parameters. Experimental result s showed that the system scheme and hardware & software were rational, carried out required functions.
The hardware of this topic was designed by Protel99 SE, the hardware emulator was designed by base Keil c V3.60.When the system was debugged, it carried out all required precision.

Keywords：Heart-rate；Filter；Amplifier；Pulse counting

摘要 I
ABSTRACT II
第1章引言 1
1.1 背景 1
1.2 研究内容 2
第2章装置组成与工作原理 3
2.1 心率测试仪的装置组成 3
2.1.1 AT89S52单片机 3
2.1.2 传感器 5
2.1.3放大器 5
2.1.4 滤波器 6
2.1.5保护系统 7
2.1.6 显示电路 7
2.2 心率测试仪的工作原理 8
第3章装置的硬件电路设计 9
3.1 电源部分 9
3.2 传感器信号和滤波部分 9
3.3 放大电路和保护电路 9
3.3.1 放大电路 9
3.3.2 保护电路 10
3.4 单片机外围及显示电路…………………………………………………………11
3.5 整体电路…………………………………………………………………………11
第4章软件设计 13
4.1 程序流程图 13
4.2上电复位电路……………………………………………………………………13
4.3 循环………………………………………………………………………………14
4.4 显示电路…………………………………………………………………………15
第5章电路调试 17
5.1 电路调试前的准备工作…………………………………………………………17
5.2 电路调试…………………………………………………………………………17
5.2.1 通电观察………………………………………………………………………17
5.2.2 静态调试………………………………………………………………………18
5.2.3 动态调试………………………………………………………………………18
5.3 调试总结…………………………………………………………………………18
第6章结束语 20
致谢 21
参考文献 22