论文编号:JD919   论文字数:8353,页数:31

摘要
 多功能时钟打点系统采用AT89C51单片机作为核心器件控制外围元件实现多功能智能打点，即实现在设定多种时刻，多种情况进行响铃。该系统的工作过程是利用AT89C51单片机读时钟芯片DS1302并与EEPROM中设定的打点时间相比较，若与设定的打点时刻相吻合，就通过AT89C51控制音乐芯片响铃。此外，该系统还设置有键盘和LCD显示，可以实现对打点时刻的设置，设置的数据将保存在EEPROM中。由于采用的是EEPROM所以该系统在掉电时仍然能保存预先设置的数据，而保持原有的响铃时间。
 关键词：   AT89C51单片机   时钟芯片DS1302   EEPROM

Abstract
  Multi-functional clock get ready system abandon whom tradition ring bell tedious , instead of modernization beautiful , pleasant environmental music, let student immerse in beauty of the music in each ring tones , experience the glamour of the music, form the joyful mental state . Not only activate students' artistic cell but also reach and optimize and educate people's environment, mould the result of student's sentiment. Advance quality-oriented education virtually, build the good campus atmosphere. The school and some enterprises and institutions use this system as going to school and leave school , signal of the daily schedule on and off duty ,etc. extensively.
 Multi-functional clock get ready system adopt AT89C51 one-chip computer control as key device peripheral component realize multi-functional intelligence get ready, namely realize sounding the bell in many kinds of situations at the moment of establishing a lot of kind. System this working course to spend AT89C51 one-chip computer read clock chip DS1302 and get ready time compare with with whom EEPROM set for, get ready constantly identical with establish , control the chip loud bell of music through AT89C51. In addition should systematic to set up keyboard and LCD show , can realize to establishment to get ready the moment also, the data set up will be kept in EEPROM. Because that adopted is EEPROM this system can still keep the data set up in advance while losing the electricity, and keep already existing loud bell time.

目录
摘要 I
Abstract II
一、方案设计与论证 1
1．1系统整体方案论证 1
方案一 1
方案二 1
1．2电路的方案设计与比较 2
1.2.1时钟模块 2
1.2.2 存储模块 3
1.2.3 显示模块 3
1.2.4 按键模块 4
1.2.5 响铃模块 4
1.2.6 单片机模块 5
二、电路设计 6
2.1 时钟单元及时间校正电路设计 6
2.1.1  DS1302时钟芯片结构和功能 8
2.1．2 DS1302在测量系统中的硬件电路 11
2.1．3读DS1302时的MCS51汇编语言程序 13
2.2 键盘模块单元电路设计 14
2.3 储模块单元电路设计 19
2.4 LCD显示模块单元电路设计 20
三、测试方法与测试结果 25
3.1 测试仪器 25
3.2 测试结果 25
总结 27
参考文献 28

相关论文 仓库温湿度检测系统的设计 基于单片机的自行车里程及车速报警系.. 基于单片机的高精度万年历设计 基于单片机的无线病房呼叫系统设计 基于单片机的多功能数字密码锁设计 基于ZigBee的智能家居环境监测系统设计 声控报警器设计